IEC TR 62225 pdf download – Guidance on terms for connectors and mechanical structures in electronic equipment

admin
IEC TR 62225 pdf download – Guidance on terms for connectors and mechanical structures in electronic equipment

IEC TR 62225 pdf download – Guidance on terms for connectors and mechanical structures in electronic equipment
1 Scope
The content of this list of terms is based on the terminology which is primarily used in the lECpublications under the responsibility of lEC TC 48.This technical report is not meant to beconsidered as a vocabulary nor as a glossary of terms in the sense of ISO/DIS 1087-1 and isnot formatted in the same way.
This technical report offers project leaders the listed terms as a preferred selection for use innew publications.By applying these preferred terms,the clause containing terms anddefinitions that form part of most standards can be shortened significantly.
The listed terms are collected from standards,already published, and projects which havereached the cDv stage.
The terms that have been published in lEC 60050-581 are listed “for information”. Modificationsare allowed if necessary, in order to better suit the purpose of new publications.The listing alsoincludes terms published in other chapter(s) of the lEV,when the term(s) have been used inTC 48 documents.
NOTE The terms as published by the lEV are not always in conformance with ISO/IEC Directives Part 2 – 2000,C.1.5.3. In this document, words like ‘a’ or “the’ have been deleted wherever possible,without indicating that theIEv was “modified”.
At the end of their maintenance cycle, it is recommended to revise published documents whereapplicable using these preferred terms.
For easy use, the terms are given in alphabetical order, with the title, description and additionalinformation about the source, status and recommendations:
.Description:
where applicable, a note is added to clarify.
. source:
the publication or project in which the term has been used.
.Status:
the following status types (in alphabetical order) have been used:
Deprecated
an IEV term, which has been replaced by a better term.
Draft
the term forms part of a document,which is currently in preparation.
Modifiedthe listed term deviates from a published term.
Obsoletethe published term is no longer in use.
Publishedthe term has been published in an lEC document.
superseded the term has been superseded by another published term.Unique
fully new term that has not been used in any document.
.Apply:
recommendation to the author of a new or a revised standard.
2Reference documents
IEC 60050-151,International Electrotechnical Vocabulary – Part 151: Electrical and magneticdevices
IEC 60050-581,International Electrotechnical Vocabulary – Chapter 581:Electromechanicalcomponents for electronic equipment
IEC 60050-826, International Electrotechnical Vocabulary – Chapter 826:Electrical installationsof buildings
IEC 60068-1,Environmental testing -Part 1: General and guidance
IEC 60309-1,Plugs,socket-outlets and couplers for industrial purposes – Part 1: Generalrequirements
lEC 60352-2,Solderless connections – Part 2: Solderless crimped connections – Generalrequirements, test methods and practical guidance
IEC 60352-3,Solderless connections – Part 3: Solderless accessible insulation displacementconnections – General requirements,test methods and practical guidance
IEC60352-4, Solderless connections – Part 4: Solderless non-accessible insulationdisplacement connections – General requirements, test methods and practical guidance
IEC 60352-7,Solderless connections – Part 7: Spring clamp connections – Generalrequirements, test methods and practical guidance 1
lEC 60512-3,Electromechanical components for electronic equipment – Basic testingprocedures and measuring methods – Part 3: Current-carrying capacity tests
IEC60512-4,Electromechanical components for electronicequipment; basic testingprocedures and measuring methods – Part 4: Dynamic stress tests
IEC 60664-1,Insulation coordination for equipment within low-voltage systems – Part 1:Principles,requirements and tests
IEC 60917-1,Modular order for the development of mechanical structures for electronicequipment practices – Part 1: Generic standard
IEC 60917-2,Modular order for the development of mechanical structures for electronicequipment practices – Part 2: Sectional specification – Interface co-ordination dimensions forthe 25 mm equipment practice
IEC 60917-2-2,Modular order for the development of mechanical structures for electronicequipment practices – Part 2: Sectional specification – Interface co-ordination dimensions forthe 25 mm equipment practice – Section 2: Detail specification – Dimensions for subracks,chassis, backplanes,front panels and plug-in units
lEC 60999-1,Connecting devices – Electrical copper conductors – Safety requirements forscrew-type and screwless-type clamping units – Part 1: General requirements and particularrequirements for clamping units for conductors from o,2 mm2 up to 35 mm3 (included)
IEC 61076-1,Connectors with assessed quality,for use in d.c., low frequency analogue and indigital high speed data applications – Part 1: Generic specification