IEC 60137 pdf download – Insulated bushings for alternating voltages above 1 000 V
1scope
This International Standard specifies the characteristics and tests for insulated bushings.
This standard is applicable to bushings, as defined in Clause 3,intended for use in electricalapparatus,machinery,transformers, switchgear and installations for three-phase alternatingcurrent systems, having highest voltage for equipment above 1 000 v and power frequenciesof 15 Hz up to and including 60 Hz.
Subject to special agreement between purchaser and supplier, this standard may be applied.in part or as a whole, to the following:
bushings used in other than three-phase systems;bushings for high-voltage direct current systems;bushings for testing transformers;
bushings for capacitors.
Special requirements and tests for transformer bushings in this standard apply also to reactorbushings.
This standard is applicable to bushings made and sold separately.Bushings which are a partof an apparatus and which cannot be tested according to this standard should be tested withthe apparatus of which they form part.
2Normative references
The following referenced documents are indispensable for the application of this document.For dated references, only the edition cited applies. For undated references, the latest editionof the referenced document (including any amendments) applies.
IEC 60038:1983.IEC standard voltages
Amendment 2 (1997y
IEC 60050(212):1990,International Electrotechnical Vocabulary – Part 212: Insulating solids,siquids and gases
IEC 60059,IEC standard current ratings
IEC 60060-1, High-voltage test techniques – Part 1:General definitions and tesf requirements
IEC 60068-2-17:1994,Basic environmental testing procedures – Part 2: Tests – Test Q:sealing
IEC 60071-1,Insulation co-ordination – Part 1: Definitions,principles and rules
IEC 60076-5,Power transformers – Part 5: Ability to withstand short circuit
IEC 60076-7: Power transformers – Part 7: Loading guide for oil-immersed transformers
IEC 60216-2,Electrical insulating materials – Thermal endurance properties – Part 2:Determination of thermal endurance properties of electrical insulating materials – Choice oftestf criteria
IEC 60270,High-voltage test techniques – Partial discharge measurements
IEC 60376,Specification of technical grade sulfur hexafluoride (SF6) for use in electricalequipment
IEC 60480,Guidelines for the checking and treatment of sulphur hexafluoride(SF6) takenfrom electrical equipment and specificafion for its re-use
IEC 60505,Evaluation and qualification of electrical insulation systems
IEC 60815,Guide for the selection of insulators in respect of polluted conditions
IEC 61462,Composite insulators – Hollow insulators for use in outdoor and indoor electricalequipment – Definitions, test methods,acceptance criteria and design recommendations
IEC 61463,Bushings – Seismic qualification
IEC 62155,Hollow pressurised and unpressurised ceramic and glass insulators for use inelectrical equipment with rated voltages greater than 1 ooo v
IEC 62217,Polymeric insulators for indoor and outdoor use with nominal voltage greater than1 000 v – General definitions, test methods and acceptance criteria
IEC 62271(all parts),High-voltage switchgear and controlgear
IEc 62271-1,High-voltage switchgear and controlgear – Part 1: Common specificationsIEC Guide 109,Environmental aspects – Inclusion in electrotechnical product standards
lEC Guide 111,Electrical high-voltage equipment in high-voltage substations – Commonrecommendations for producf standards
CISPR 16-1(all parts),Specification for radio disturbance and immunity measuring apparatusand methods
CISPR 18-2,Radio interference characteristics of overhead power lines and high-voltageequipment – Parts 2: Methods of measurement and procedure for determining limits
3Terms and definitions
For the purposes of this document,the following terms and definitions apply.
3.1
bushing
device that enables one or several conductors to pass through a partition such as a wall or atank,and insulates the conductors from it; the means of attachment (flange or fixing device)to the partition forms part of the bushing
[IEV 471-02-01]
NOTE1 The conductor may form an integral part of the bushing or be drawn into the central tube of the bushing.NOTE 2 The bushing may be of the types as described in 3.2 to 3.21.
IEC 60137 pdf download – Insulated bushings for alternating voltages above 1 000 V
